![cooler master hyper 212 evo install on cyberpowerpc cooler master hyper 212 evo install on cyberpowerpc](https://www.cyberpowerpc.com/images/cs/amethyst_new/blk05_400.png)
The cooler was slightly loose and the paste I have probably dried up a bit. You probably won't notice that small little leak until the damage is done. You'll notice when your fan starts to die. There are just way too many points of failure. Unless you're going to overvolt like hell to overclock, I'd -never- recommend water cooling. Pretty cheap and it's survived multiple road trips from the east coast to the west coast and back without me needing to remount it. And on my girlfriend's PC, I bought her this heatsink. I use this heatsink on my old Intel 2500k, which is overclocked pretty heavily to 4.5ghz. I prefer the ones with the metal back plate the heatsink screws into. Those little plastic pushpins are garbage, and I bet one has just popped out.
![cooler master hyper 212 evo install on cyberpowerpc cooler master hyper 212 evo install on cyberpowerpc](https://i.imgur.com/rtXaVlb.jpg)
I have been building PCs since I was 8, with a 386 as my first build, and I've -never- been as frustrated as I when I tried using the stock heatsink Intel's pushing out nowadays. Are you using the stock Intel heatsink? That thing is as crap as crap can get. Oh and here is a picture of the shit Intel stock cooler when it was on the test bench for ten minutes, before being thrown in the trash where it Echoing what a few other posters have said. In a game like The Witcher, the CPU will get up to the mid to high 40's. Granted, Diablo isn't exactly a CPU intensive game, but I think this is a good representation of what an average game's CPU usage is like. Notice the temperature - that's what the chip idles at. Here's an example - this is two hours of playing Diablo 3 at max settings on a 4790k with the Noctua NH-D14. During normal gaming usage, the Noctua is so good that the 4790k temps hardly rise above idle. Overclocked to 4.6 Ghz at 1.3v, the same test got the CPU up to about 74c. I mounted a Noctua NH-D14, ran the same test for an hour, and it never went above 66c. I ended the test right away, pulled off the stock cooler, and threw it directly in the trash. The CPU hit 100c in under a minute and started thermal throttling at stock clock speeds and voltage. When I first got the CPU the week they were released, I hooked up the stock cooler and ran a Prime95 In-Place Large FFT. It's tiny and lightweight and the fan on it actually made me chuckle it's so pathetic looking.
![cooler master hyper 212 evo install on cyberpowerpc cooler master hyper 212 evo install on cyberpowerpc](https://i.ytimg.com/vi/nyubK1oVzis/maxresdefault.jpg)
Cooler master hyper 212 evo install on cyberpowerpc Pc#
Generally, in is from the front and side, out is back and Yeah.I actually have a PC with the same CPU the OP has, the Devil's Canyon 4790k, and I stress tested it in a similar way when I first got it. Intake fans need to send the cool air to the components, at which point it gets hotter and needs to be pushed out by the "outtake(?)" fans, in which case, the path needs to be clear also, so as to not trap the hot air in. Quite simply, having big or fast fans isn't good enough if the air being sucked in is blocked by big power wires, graphic cards, etc. Otherwise, you might just need to get yourself some thermal paste and a good third party cooler (Cooler Master Hyper 212 Evo is a popular, good bang-for-your-buck choice.)Įdit: I saw you weren't too sure about airflow. Good airflow can be more difficult depending on your case and wiring, but you should make sure there's as much empty space as possible between the different fans (front to back, side to top, as the case may be.) You should also check if the fan is working properly. Mine is only a little over room temperature.Īt that point, I doubt it's dust related, but I would try to give it a good cleaning.